The Y site IV tubing is an IV tubing with a Y injection site or Y site, a type of injection port. Y site is the location of ports where you can attach another IV line or a syringe for IV push medication.
The IV set is generally used to administer intravenous fluids, such as maintenance solutions and medications, into the body. Intravenous administration includes a single injection with subsequent catheter insertion into the vein. Through the Y port, medical workers can add medicines or deliver multiple doses of fluids without injecting the patient for each occurrence. So, Y port IV tubing is very useful for infusion. Check out one of our Y site IV tubings in South America.
An IV set mainly comprises flexible tubing made from medical polyvinyl chloride (PVC) with various parts. The tubing allows the desired fluid to be delivered into the patient’s body through the vein. The fluid flow is aided by gravity, which is called gravity driven. This is why the IV set is permanently placed higher than the patient. Maintaining its quality is essential for safe and effective treatment delivery. Click here to know the top culprits that lead to tubing breakage.
Medical PVC is widely used in medical equipment because it is low-cost, compressible, and safe for medical use under all circ*mstances. Compressibility allows medical staff to remove air bubbles along with the tubing.
Shop All Types of IV Sets
Parts of Y Site IV Tubing
Plastic Spike
Some parts are attached to the tubing. The uppermost part of the Y site IV tubing is a plastic spike with a cap and air vent, which will be plugged into the desired intravenous fluid container. The plastic spike is made from acrylonitrile butadiene styrene (ABS), which is rigid and resistant to impact, which makes it tough enough to penetrate rubber plugs of intravenous fluid containers. The fluid will then flow through the spike tip to the drip chamber. When it is not plugged in, the cap is attached to ensure the hygiene of the spike. The cap must always be sterile to avoid contamination, and any manipulation would require prior sanitization.
Drip Chamber
The drip chamber connects with the spike. Intravenous fluid collects in the drip chamber before entering the tubings. It is the site where medical staff observe the flow rate and confirm the flow. The drip chamber is made from medical PVC, which is flexible and compressible. This is so that the drip chamber can be compressed when necessary, such as to decrease the volume of fluid flowing into the drip chamber. At the bottom of the drip chamber is the solution filter, where the infusion fluid is suspended. As its name suggests, it is a filter that sieves out unwanted particles, such as debris and pathogenic microorganisms, that have contaminated the intravenous fluid.
Explore more types of drip chambers
Flow Regulator
Following the drip chamber is the flow regulator, which is in charge of maintaining the prescribed flow rate of the infusion fluid. The flow regulator includes the roller clamp, which is made from polyethylene (PE) or ABS. PE is strong, lightweight, and resistant to corrosion as well as chemicals. The roller clamp regulates the fluid flow rate by compressing the tubing without damaging it. It can also half-fluid flow entirely when needed.
Explore more types of roller clamps
Y Injection Port
Subsequently, there is the Y injection port. The Y injection port is a three-way connector in which two ends are adjacent to the tubing of the IV set, and one end is the injection site. The Y injection port is made from ABS and isoprene or natural rubber. Isoprene is its latex-free rubber, which is suitable for those with latex allergies. As mentioned previously, ABS is rigid and has resistance to chemicals, heat, and physical manipulation. This is why it is used for the Y injection port.
There are many types of injection sites. Each of them is used in different conditions, depending on the patient’s requirements. The injection sites are essential such that they serve as the point of entry for vaccines, drugs, or therapeutic medicine into the patient’s body. Depending on the type of injection site, syringes with needles attached may or may not be required, as there are needleless attachments on certain injection sites. The Y injection site is made from natural rubber or isoprene. Similarly, the isoprene equivalent is latex-free. The Y injection site is covered by a leak-proof non-removable rubber membrane which allows for the acute administration of emergency drugs into the patient’s body.
Contact us for price!
Luer Lock Connector and Hypodermic Needle
The Y injection port is then followed by the rotating Luer lock connector. This attaches the hypodermic needle to the tubing. The hypodermic needle is the last component of the Y site IV tubing. It is the structure that pierces the vein of the patient and connects the IV set to the patient’s body directly. The diameter of the needle indirectly regulates the flow rate, such that the wider the diameter, the higher the flow rate.
Shop All Types of IV Sets parts
Benefits of Y Site IV Tubing
The Y site IV tubing can provide a secondary point of access in the patient’s intravenous tubing, allowing the intermittent infusion of additional intravenous fluids such as medications. This means the second infusion fluid would be attached to the same line as the primary IV set. The most common primary fluid is maintenance fluids, such as a regular saline infusion. The secondary fluid administered through the Y injection site is usually medication, such as an antibiotic.
The benefit of the Y site IV tubing is that two fluids can be administered at the same time. For example, healthcare workers can administer a carrier and a medication or two medications simultaneously. This reduces the requirement of connections and disconnections of IV sets, which saves time for healthcare providers and greatly decreases the risk of contamination. The Y site IV tubing must be set up correctly for the infusion of the secondary fluid to be carried out smoothly.
Related Articles
Tag: IV injection Tag: infusion set with rubber injection site Tag: IV parts Tag: PE flow regulator Tag: y site Tag: infusion set without needle Tag: ABS Luer lock connector Tag: IV set parts uses Tag: Types of IV Set Injection Sites Tag: infusion set with luer lock connector Tag: infusion set parts uses Tag: infus set type y Tag: disposable IV sets Tag: air bubble in iv
